*#06# returns IMEI number and SoftwareVersion (not HC600).
These are the pinouts for the HC600 they are the same as the 800/1000 I beleive.
1 3 5 7 9 11 13 15
I I I I I I I I
O O 17
I I I I I I I I
2 4 6 8 10 12 14 16
1 Vbat_ext 9 SDA_E
2 EMMI_PAE 10 GND
3 Mic 11 GND
4 EMMI_OPE 12 DC_IN (charge)
5 GND 13 Speaker
6 EXT_EMET 14 MARCHE
7 SCL_E 15 DC_IN (charge)
8 EXT_RECDIT 16 GND
17 Antenna+internal switch (int/ext)
Bosch 718
*#3262255*8378# (*#DANCALL*TEST#) to makesecret Engineering menu (menu 10) appear.
10. Engineering 10.1 MS Info 10.1.1 on 10.1.2 off 10.2 Software details 10.2.1 Software version 10.2.2 EEPROM version 10.2 Test / Production details 10.3.1 Hardware data 10.3.2 Production data 10.3.3 Service data 10.3.4 Mechanical data
*#06# to display the IMEI (International Mobile Equipment Identity) *#0000# to set the language automaticaly (Reset to english) *#3370# to set the Enhaced Full Rate #3370# to Reset the phone *#9000# to enter sim lock code *#9001# To enter the corporate code (Bosch 908) *#9002# To enter the provider code (Bosch 908) *#9003# to enter the network code *#9004# to enter the subset code *#9100# to remove the sim lock permanently *#9101# to remove the corporate lock permanently *#9102# to remove the provider lock permanently *#9103# to remove the network lock permanently *#9104# to remove the subset lock permanently
(SIM-lock is NOT the SP-lock/Service Provider lock!!)
The SIM-lock makes your phone to fusion with the SIM-card, and the phone will not acceptany other SIM cards after you lock your phone! You get ten chances to type the correctcode! After the tenth time your phone gets "SIM-lock permanently blocked", andyou will be unable to open it !! The best thing you can do is to remove the SIM-lockpermanently!!
Bosch 738
*#3262255*8378# (*#DANCALL*TEST#) to makesecret Engineering menu (menu 10) appear.
10. Engineering 10.1 MS Info 10.1.1 on 10.1.2 off 10.2 Software details 10.2.1 Software version 10.2.2 EEPROM version 10.2 Test / Production details 10.3.1 Hardware data 10.3.2 Production data 10.3.3 Service data 10.3.4 Mechanical data
*#06# to display the IMEI (International Mobile Equipment Identity) *#0000# to set the language automaticaly (Reset to english) *#3370# to set the Enhaced Full Rate #3370# to Reset the phone *#9000# to enter sim lock code *#9001# To enter the corporate code (Bosch 908) *#9002# To enter the provider code (Bosch 908) *#9003# to enter the network code *#9004# to enter the subset code *#9100# to remove the sim lock permanently *#9101# to remove the corporate lock permanently *#9102# to remove the provider lock permanently *#9103# to remove the network lock permanently *#9104# to remove the subset lock permanently
(SIM-lock is NOT the SP-lock/Service Provider lock!!)
The SIM-lock makes your phone to fusion with the SIM-card, and the phone will not acceptany other SIM cards after you lock your phone! You get ten chances to type the correctcode! After the tenth time your phone gets "SIM-lock permanently blocked", andyou will be unable to open it !! The best thing you can do is to remove the SIM-lockpermanently!!
The 54# Tip Type 1#, 2#........54# on the keypad (when you're not in the menu) to get the phone numberused for with this key when speed dialing0000
Bosch 908
*#3262255*8378# (*#DANCALL*TEST#) to makesecret Engineering menu (menu 10) appear.
10. Engineering 10.1 MS Info 10.1.1 on 10.1.2 off 10.2 Software details 10.2.1 Software version 10.2.2 EEPROM version 10.2 Test / Production details 10.3.1 Hardware data 10.3.2 Production data 10.3.3 Service data 10.3.4 Mechanical data
*#06# to display the IMEI (International Mobile Equipment Identity) *#0000# to set the language automaticaly (Reset to english) *#3370# to set the Enhaced Full Rate #3370# to Reset the phone *#9000# to enter sim lock code *#9001# To enter the corporate code (Bosch 908) *#9002# To enter the provider code (Bosch 908) *#9003# to enter the network code *#9004# to enter the subset code *#9100# to remove the sim lock permanently *#9101# to remove the corporate lock permanently *#9102# to remove the provider lock permanently *#9103# to remove the network lock permanently *#9104# to remove the subset lock permanently
(SIM-lock is NOT the SP-lock/Service Provider lock!!)
The SIM-lock makes your phone to fusion with the SIM-card, and the phone will not acceptany other SIM cards after you lock your phone! You get ten chances to type the correctcode! After the tenth time your phone gets "SIM-lock permanently blocked", andyou will be unable to open it !! The best thing you can do is to remove the SIM-lockpermanently!!
The 54# Tip Type 1#, 2#........54# on the keypad (when you're not in the menu) to get the phone numberused for with this key when speed dialing0000
Bosch 909
*#06# to display the IMEI (InternationalMobile Equipment Identity) *#0000# to set the language automaticaly (Reset to english) *#3370# to set the Enhaced Full Rate #3370# to Reset the phone *#9000# to enter sim lock code *#9001# To enter the corporate code (Bosch 908) *#9002# To enter the provider code (Bosch 908) *#9003# to enter the network code *#9004# to enter the subset code *#9100# to remove the sim lock permanently *#9101# to remove the corporate lock permanently *#9102# to remove the provider lock permanently *#9103# to remove the network lock permanently *#9104# to remove the subset lock permanently *#3262255*8378# (*#DANCALL*TEST#) and you will get a hidden 10th menu
Bosch COM607
*#3262255*8378# (*#DANCALL*TEST#) to makesecret Engineering menu (menu 10) appear.
10. Engineering 10.1 MS Info 10.1.1 on 10.1.2 off 10.2 Software details 10.2.1 Software version 10.2.2 EEPROM version 10.2 Test / Production details 10.3.1 Hardware data 10.3.2 Production data 10.3.3 Service data 10.3.4 Mechanical data
*#06# to display the IMEI (International Mobile Equipment Identity) *#0000# to set the language automaticaly (Reset to english) *#3370# to set the Enhaced Full Rate #3370# to Reset the phone *#9000# to enter sim lock code *#9001# To enter the corporate code (Bosch 908) *#9002# To enter the provider code (Bosch 908) *#9003# to enter the network code *#9004# to enter the subset code *#9100# to remove the sim lock permanently *#9101# to remove the corporate lock permanently *#9102# to remove the provider lock permanently *#9103# to remove the network lock permanently *#9104# to remove the subset lock permanently
(SIM-lock is NOT the SP-lock/Service Provider lock!!)
NOKIA 3110
*#06# for checking the IMEI (International Mobile Equipment Identity) Information youget from the IMEI:
XXXXXX XX XXXXXX X
TAC FAC SNR SP
TAC = Type approval code FAC = Final assembly code SNR = Serial number SP = Spare
*#7780# restores Factory Settings..(Memory, language, counters not included)
*#3110# for checking the phone's software (SW) - called firmware revision information.
#746025625# [*#sim0clock#] Checks if the sim clock can be stopped. Sim clock stop is a kind of stand-by mode whichwill save battery time. This code doesn't work with software version 4.59.
*#92702689# [*#war0anty#] Press the following warranty code:
6232 (OK) : Displays the Month and Year of Manufacture (0997) 7332 (OK) : Displays the date of the last repairment - if found ('DATE NOT SAVED'...) 7832 (OK) : Displays (if found) the date where the phone was purchased ('DATE NOTSAVED'...) 9268 (OK) : Displays Serial Number 37832 (OK) : Set the Purchasing Date MMYY (Warning: You can only do this once - So becareful ...) 87267 (OK) : Transfers ALL phone numbers, pictures, sounds from one phone to another
Service Prover Lock The service provider (SP) lock is used to lock the cell phone to the SP's SIM card. Oncethe cell phone is locked to a specific operator, if one inserts a SIM card from adifferent operator the phone will refuse to accept it! The cell phone will however acceptanother SIM card from the same operator.
All Nokia phones (2110 and newer) have four different SIM locks which can be used to lockthe phone for upto 4 different providers. But most phones with restriction only have onelock activated. ( lock 1)
The main code used in Nokia phones is: #pw+(master code)+Y# This code is able to check, activate or remove Sim card restriction (SP-lock). Use the * key to get the p, + and w chars. 'Y' has to be 1,2,3 or 4 - depending of what lock you what to deal with.
#pw+1234567890+1# for Provider-Lock status #pw+1234567890+2# for Network-Lock status #pw+1234567890+3# for Country-Lock status #pw+1234567890+4# for SimCard-Lock status
# = DOUBLE-CROSS W = PRESS "*" THREE TIMES P = PRESS "*" FOUR TIMES + = PRESS "*" TWO TIMES MASTERCODE = 1234567890 Y = NUMBER 1 TO 4
(master code) is a 10 digit code, based on the phones IMEI number. (I can NOT give you the master code - SO DON'T ASK ME FOR IT !!!!!!!)
Eg. To remove restriction on lock 1 type following code: #pw+(master code)+1# If you just want to check your phone use 10 random numbers Eg. 1234567890 as the (mastercode) eg. To check if phone if restricted on lock 1 type the following code: #pw+1234567890+1#
Please NOTE that these codes could be used with care! A user told me that it's onlypossible to type in about 3 different codes on each lock! Then something bad will happen..therefore be careful!
Bypass the SP lock With a Nokia 16xx/21xx/31xx/51xx/81xx that are SIMlocked to one privider you can bypassthe SP lock like this: 1: Insert sim card of diferent provider. 2: Turn on the phone and press the UP VOLUME key for 3 sec. then release it and the phonesays PIN CODE? 3: Press the "C" key. 4: Then Press * and wait until it desapear and apear again, then press * one more time and04*PIN*PIN*PIN#
The phone now says: PIN CODE CHANGED (or ACCEPTED) and the SIM card is accepted until yourestart the phone again. NOTE: On version 5.04 Nokia has removed this option !
Fast silent mode In the newer versions (v.7.11 or higher) a quick silent mode can by entered. Press Menuthen #.
The 54# Tip: Type 1#, 2#........54# on the keypad (when you're not in the menu) to get the phone numberused for with this key when speed dialing
NOKIA 3310
*#06# for checking the IMEI (International Mobile Equipment Identity) Information you getfrom the IMEI:
XXXXXX XX XXXXXX X
TAC FAC SNR SP
TAC = Type approval code FAC = Final assembly code SNR = Serial number SP = Spare
*#0000# To view Software Version.
*#746025625# [*#sim0clock#] Checks if the sim clock can be stopped. Sim clock stop is a kind of stand-by mode whichwill save battery time. This code doesn't work with software version 4.59.
*#92702689# [*#war0anty#] takes you to a secret menu with 6 choices:
1. Displays Serial Number. 2. Displays the Month and Year of Manufacture (0997) 3. Displays (if there) the date where the phone was purchased (MMYY) 4. Displays the date of the last repairment - if found (0000) 5. makes you capebel of transferring user data if you have the gear for it 6. shows how many hours the phone has been on
Latest software version: V 05.36 NSE - 8/9 (25-07-00)
V 5.31 NSE - 8/9 (24-05-00) V 5.26 NSE - 8/9 (07-04-00) V 5.02 NSE - 8/9 V 4.41 NSE - 8/9 (17-08-99)0 V 4.11 (???) V 3.10 NSE - 8
*3370# - Enhanced Full Rate Codec (EFR) activation. It will automatically restart. #3370# - Enhanced Full Rate Codec (EFR) deactivation. It will automatically restart. *4370# - Half Rate Codec activation. It will automatically restart #4370# - Half Rate Codec deactivation. It will automatically restart xx# - xx position in Phone Book
Enhanced Full Rate will give you much better sound quality when you enable it. The newEnhanced Full Rate CODEC adopted by GSM uses the ASELP (AlgebraicCode Excitation LinearPrediction) compression technology. This technology allows for much great voice quality inthe same number of bits as the older Full Rate CODEC. The older technology was calledLPC-RPE (Linear Prediction Coding with Regular Pulse Excitation). Both operate at 13kilobits.(but you take up more space on the network, so they can charge you more) -Talk-time is reduced with about 5%
Free SMS Tip 1st Way: 1. turn our phone off. 2. turn it on and enter your pin. 3. enter *#746025625# 4. now "SIM CLOCK STOP ALLOWED" will be displayed. now you can send sms for free. if you turn your phone off and later on you have to reenterthis code!!! In some Networks it doesn't work!!! 2nd Way: Set Menu 4-3-3 on Usergroup 666 (work with German Networks). It's now the group 999, butit's not tested yet
NOKIA 5110
*#06# for checking the IMEI (International Mobile Equipment Identity) Information you getfrom the IMEI:
XXXXXX XX XXXXXX X
TAC FAC SNR SP
TAC = Type approval code FAC = Final assembly code SNR = Serial number SP = Spare
*#0000# To view Software Version.
#746025625# [*#sim0clock#] Checks if the sim clock can be stopped. Sim clock stop is a kind of stand-by mode whichwill save battery time. This code doesn't work with software version 4.59.
*#92702689# [*#war0anty#] You don't need the warranty-codes any more - you can just scroll through the informationlike in any other menu. It has the the same data as 81xx and 31xx phones (with"Edit" button for purchase date, and "User data transfer".
Menu: 1: Displays Serial Number. 2: Displays the Month and Year of Manufacture (0997) 3: Displays (if there) the date where the phone was purchased (MMYY) you can here set thePurchasing Date (Warning: You can only do this once - so be careful what you write...) 4: Displays the date of the last repairment - if found (0000) 6: Does anyone know if this is for upgrading the phone's EEPROM?? (Transfer user data?)
Enhanced Full Rate Codec (EFR): On: Enter *3370# and EFR will be activated after a reboot of the phone ( consumes morepower ) Off: Enter #3370# and EFR will be switched off after a reboot of the phone.
Half Rate Codec: On: Enter *4720# and Half Rate coded will be activated after a reboot of the phone (better standby time ) Off: Enter #4720# and Half Rate coded will be de-activated after a reboot of the phone
Enhanced Full Rate will give you much better sound quality when you enable it. The newEnhanced Full Rate CODEC adopted by GSM uses the ASELP (AlgebraicCode Excitation LinearPrediction) compression technology. This technology allows for much great voice quality inthe same number of bits as the older Full Rate CODEC. The older technology was calledLPC-RPE (Linear Prediction Coding with Regular Pulse Excitation). Both operate at 13kilobits.(but you take up more space on the network, so they can charge you more) -Talk-time is reduced with about 5%
Half Rate will give you bad soundquality, which gives the serviceprovider the opportunityto have more calls on the network, and you might get a lower charge from them. - Will giveyou 30% longer talk-time.
Network Monitor There is a hidden menu inside your Nokia phone. If you want to activate it, you'll have tore-program some chips inside of your phone.
1.Check your software version. You can only continue if you have v4.33, v4.73 or v5.24. 2.Take apart the phone. 3. De-solder the EEPROM (ATMEL AT 24C64). 4. Read out the data with an EEPROM programmer and save it to a file (Backup). 5. If you have v.33 or v4.73, change the address "03B8" from "00" to"FF". 6. If you have v5.24 then change the address "0378" from "00" to"FF". 7. Write the new data to the EEPROM and solder it back to the phone. 8. Power on your phone and you should have "Netmonitor" enabled.
The Network Monitor gives you the following information.
Carrier number
MS RX Level in DBM
Received signal quality
MS TX power level C1 (Path loss criterion, used for cell selection and reselection). Therange is -99 to 99.
RTL (Radio link timeout).
Timeslot
Indication of the transmitter status
Information on the Network parameters.
TMSI (Temporary Mobile Subscriber Identity).
Cell identification (Cell ID, Number of cells being used).
MCC (Mobile country code)
MCN (Mobile network code)
LAC (Location area code)
Ciphering (On/Off)
Hopping (On/Off)
DTX (On/Off)
Discard cell barred information. The Reboot Trick Should work on all software versions. 1. Go to calendar (menu - 8) 2. Make note / reminder 3. Enter some text into the edit box 4. Hold clear until whole text is cleared, then press Back 5. Press 0. Main screen is shown but a space appears on the screen. You can't see it ofcourse. 6. Enter 4 digits (1234, for example) 7. Use the down arrow to move the cursor to the left side of the numbers and the space (2times down arrow) 8. Now enter 6 digits and press the green "Call button".
Wait some seconds...the phone will now flash the background light and finally reboot. Thetrick should also work on other menus like the profile menu...
The James Bond Trick If you short-circuit theleft middle and right pins on the bottom of the phone with allconnections touching each other, the Nokia software hangs! The profile "Headset"will be activated. Before you do this just activate the "Automatic Answer" inthe headset profile and set the ringing volume to "Mute". Now you can use yourphone for checking out what people are talking about in a room. Just place it under atable in a room and call it. The phone receives the call without ringing and you canlisten to what people are saying.
Service Prover Lock The service provider (SP) lock is used to lock the cell phone to the SP's SIM card. Oncethe cell phone is locked to a specific operator, if one inserts a SIM card from adifferent operator the phone will refuse to accept it! The cell phone will however acceptanother SIM card from the same operator.
All Nokia phones (2110 and newer) have four different SIM locks which can be used to lockthe phone for upto 4 different providers. But most phones with restriction only have onelock activated. ( lock 1)
The main code used in Nokia phones is: #pw+(master code)+Y# This code is able to check, activate or remove Sim card restriction (SP-lock). Use the * key to get the p, + and w chars. 'Y' has to be 1,2,3 or 4 - depending of what lock you what to deal with.
#pw+1234567890+1# for Provider-Lock status #pw+1234567890+2# for Network-Lock status #pw+1234567890+3# for Country-Lock status #pw+1234567890+4# for SimCard-Lock status
# = DOUBLE-CROSS W = PRESS "*" THREE TIMES P = PRESS "*" FOUR TIMES + = PRESS "*" TWO TIMES MASTERCODE = 1234567890 Y = NUMBER 1 TO 4
(master code) is a 10 digit code, based on the phones IMEI number. (I can NOT give you the master code - SO DON'T ASK ME FOR IT !!!!!!!)
Eg. To remove restriction on lock 1 type following code: #pw+(master code)+1# If you just want to check your phone use 10 random numbers Eg. 1234567890 as the (mastercode) eg. To check if phone if restricted on lock 1 type the following code: #pw+1234567890+1#
Please NOTE that these codes could be used with care! A user told me that it's onlypossible to type in about 3 different codes on each lock! Then something bad will happen..therefore be careful!
Bypass the SP lock With a Nokia 16xx/21xx/31xx/51xx/81xx that are SIMlocked to one privider you can bypassthe SP lock like this: 1: Insert sim card of diferent provider. 2: Turn on the phone and press the UP VOLUME key for 3 sec. then release it and the phonesays PIN CODE? 3: Press the "C" key. 4: Then Press * and wait until it desapear and apear again, then press * one more time and04*PIN*PIN*PIN#
The phone now says: PIN CODE CHANGED (or ACCEPTED) and the SIM card is accepted until yourestart the phone again. NOTE: On version 5.04 Nokia has removed this option !
Your number in your display 1. Goto menu 3-7 Call cost settings. 2. Turn ON the Call costs' limit 3-7-1. PIN2 code Required. 3. Put in the limit with the phone number. eg. my phone # is 019 2184697 Enter the limitas 2184697 4. Goto menu 3-7-2 Show costs in. PIN2 code Required. 5. Select Currency. 6. Enter Unit price : 1 7. Enter Currency name as 019 (per my phone # eg. above) Now the phone number 019 2184697 will remains on the 4th row of the display. Secondly, ifyou press the # key, it prompt which line to be used; Line 1 or 2.
Larger Number Tip (works in 51xx series) If you hold the key # while you are in the names list, the telephone number can be viewedlarger.
Power Button Tip: If you press the button for a short moment, the menu with the profiles is shown on thedisplay. If you press one more time, the mobile turns itself off. You can use the up anddown cursor keys to scroll and enable a different alert setting.
Crazy 5110 Send a SMS full of . (dots) the it'll go crazy when you scroll the received message inyour 5110. It doesn't do any permanent damage...it only goes crazy if you scroll the SMS.I'm not sure if it works with all of the software version but it works with 4.59. Doesn'twork on SW version 4.53 ..
The 54# Tip: Type 1#, 2#........54# on the keypad (when you're not in the menu) to get the phone numberused for with this key when speed dialing.
Revealing the Headphone and Car-Kit menus Please note that if you do these next tricks, the new menus can't be erased withoutretoring the factory default settings. To do these tricks you need to short-circuit thepins on the bottom of the phone next to where you plug in you charger.
1. To activate the "Headset" menu, you need to short-circuit pins "3"and "4". After a short time the word "Headset" will be shown in thedisplay. Menu 3-6 is now enabled. 2. To activate the "Car" menu, you need to short-circuit pins "4" and"5". After a short time the word "Car" will be shown in the display.Menu 3-7 is now enabled.
Quick SMS Typing When typing SMS messages, you have to wait some seconds before you can type the nextletter if it is in the same button than the previous one. For example try to write theword "letter", you have to wait before you can enter the second "t"..A much faster solution is to press the # button twice and then the letter "t".
Free Call Tip NB. The tips needs Net Monitor enabled. Be aware that the trick wil remove Netmonitor insome sw versions like v4.73 and v5.04.
1. Laungh the NetMonitor in your Nokia 51xx / 61xx 2. Execute the test number 497 3. Free calling for about 90 sec should now have been activated.
The trick has not been comfirmed working yet.
New Menu on Emergency Calls *3001#12345# Brings a new menu that gives you access to the emergency calls ( 911 Etc. ).It will give you FREE calls! (only the ones you put in the emergency!! ) This option willdepend on your GSM operator, may be this code will not works and you still can get thebill!
NOKIA 6110
*#06# for checking the IMEI (International Mobile Equipment Identity) Information you getfrom the IMEI:
XXXXXX XX XXXXXX X
TAC FAC SNR SP
TAC = Type approval code FAC = Final assembly code SNR = Serial number SP = Spare
*#0000# To view Software Version. *#6110# Try this code if the above code doen't work.
#746025625# [*#sim0clock#] Checks if the sim clock can be stopped. Sim clock stop is a kind of stand-by mode whichwill save battery time. This code doesn't work with software version 4.59.
*#92702689# [*#war0anty#] You don't need the warranty-codes any more - you can just scroll through the informationlike in any other menu. It has the the same data as 81xx and 31xx phones (with"Edit" button for purchase date, and "User data transfer".
Menu: 1: Displays Serial Number. 2: Displays the Month and Year of Manufacture (0997) 3: Displays (if there) the date where the phone was purchased (MMYY) you can here set thePurchasing Date (Warning: You can only do this once - so be careful what you write...) 4: Displays the date of the last repairment - if found (0000) 6: Does anyone know if this is for upgrading the phone's EEPROM?? (Transfer user data?)
Enhanced Full Rate Codec (EFR): On: Enter *3370# and EFR will be activated after a reboot of the phone ( consumes morepower ) Off: Enter #3370# and EFR will be switched off after a reboot of the phone.
Half Rate Codec: On: Enter *4720# and Half Rate coded will be activated after a reboot of the phone (better standby time ) Off: Enter #4720# and Half Rate coded will be de-activated after a reboot of the phone
Network Monitor There is a hidden menu inside your Nokia phone. If you want to activate it, you'll have tore-program some chips inside of your phone.
1.Check your software version. You can only continue if you have v4.33, v4.73 or v5.24. 2.Take apart the phone. 3. De-solder the EEPROM (ATMEL AT 24C64). 4. Read out the data with an EEPROM programmer and save it to a file (Backup). 5. If you have v.33 or v4.73, change the address "03B8" from "00" to"FF". 6. If you have v5.24 then change the address "0378" from "00" to"FF". 7. Write the new data to the EEPROM and solder it back to the phone. 8. Power on your phone and you should have "Netmonitor" enabled.
The Network Monitor gives you the following information.
Carrier number
MS RX Level in DBM
Received signal quality
MS TX power level C1 (Path loss criterion, used for cell selection and reselection). Therange is -99 to 99.
RTL (Radio link timeout).
Timeslot
Indication of the transmitter status
Information on the Network parameters.
TMSI (Temporary Mobile Subscriber Identity).
Cell identification (Cell ID, Number of cells being used).
MCC (Mobile country code)
MCN (Mobile network code)
LAC (Location area code)
Ciphering (On/Off)
Hopping (On/Off)
DTX (On/Off)
Discard cell barred information. The Reboot Trick Should work on all software versions. 1. Go to calendar (menu - 8) 2. Make note / reminder 3. Enter some text into the edit box 4. Hold clear until whole text is cleared, then press Back 5. Press 0. Main screen is shown but a space appears on the screen. You can't see it ofcourse. 6. Enter 4 digits (1234, for example) 7. Use the down arrow to move the cursor to the left side of the numbers and the space (2times down arrow) 8. Now enter 6 digits and press the green "Call button".
Wait some seconds...the phone will now flash the background light and finally reboot. Thetrick should also work on other menus like the profile menu...
The James Bond Trick If you short-circuit theleft middle and right pins on the bottom of the phone with allconnections touching each other, the Nokia software hangs! The profile "Headset"will be activated. Before you do this just activate the "Automatic Answer" inthe headset profile and set the ringing volume to "Mute". Now you can use yourphone for checking out what people are talking about in a room. Just place it under atable in a room and call it. The phone receives the call without ringing and you canlisten to what people are saying.
Service Prover Lock The service provider (SP) lock is used to lock the cell phone to the SP's SIM card. Oncethe cell phone is locked to a specific operator, if one inserts a SIM card from adifferent operator the phone will refuse to accept it! The cell phone will however acceptanother SIM card from the same operator.
All Nokia phones (2110 and newer) have four different SIM locks which can be used to lockthe phone for upto 4 different providers. But most phones with restriction only have onelock activated. ( lock 1)
The main code used in Nokia phones is: #pw+(master code)+Y# This code is able to check, activate or remove Sim card restriction (SP-lock). Use the * key to get the p, + and w chars. 'Y' has to be 1,2,3 or 4 - depending of what lock you what to deal with.
#pw+1234567890+1# for Provider-Lock status #pw+1234567890+2# for Network-Lock status #pw+1234567890+3# for Country-Lock status #pw+1234567890+4# for SimCard-Lock status
# = DOUBLE-CROSS W = PRESS "*" THREE TIMES P = PRESS "*" FOUR TIMES + = PRESS "*" TWO TIMES MASTERCODE = 1234567890 Y = NUMBER 1 TO 4
(master code) is a 10 digit code, based on the phones IMEI number. (I can NOT give you the master code - SO DON'T ASK ME FOR IT !!!!!!!)
Eg. To remove restriction on lock 1 type following code: #pw+(master code)+1# If you just want to check your phone use 10 random numbers Eg. 1234567890 as the (mastercode) eg. To check if phone if restricted on lock 1 type the following code: #pw+1234567890+1#
Please NOTE that these codes could be used with care! A user told me that it's onlypossible to type in about 3 different codes on each lock! Then something bad will happen..therefore be careful!
Power Button Tip: If you press the button for a short moment, the menu with the profiles is shown on thedisplay. If you press one more time, the mobile turns itself off. You can use the up anddown cursor keys to scroll and enable a different alert setting.
The 54# Tip: Type 1#, 2#........54# on the keypad (when you're not in the menu) to get the phone numberused for with thiskey when speed dialing.
Free Call Tip NB. The tips needs Net Monitor enabled. Be aware that the trick wil remove Netmonitor insome sw versions like v4.73, v5.04 and v5.24.
1. Laungh the NetMonitor in your Nokia 51xx / 61xx 2. Execute the test number 497 3. Free calling for about 90 sec should now have been activated.
The trick has not been comfirmed working yet.
Revealing the Headphone and Car-Kit menus Please note that if you do these next tricks, the new menus can't be erased withoutretoring the factory default settings. To do these tricks you need to short-circuit thepins on the bottom of the phone next to where you plug in you charger.
1. To activate the "Headset" menu, you need to short-circuit pins "3"and "4". After a short time the word "Headset" will be shown in thedisplay. Menu 3-6 is now enabled. 2. To activate the "Car" menu, you need to short-circuit pins "4" and"5". After a short time the word "Car" will be shown in the display.Menu 3-7 is now enabled.
Quick SMS Typing When typing SMS messages, you have to wait some seconds before you can type the nextletter if it is in the same button than the previous one. For example try to write theword "letter", you have to wait before you can enter the second "t"..A much faster solution is to press the # button twice and then the letter "t".
NOKIA 9110
*#06# for checking the IMEI (International Mobile Equipment Identity) *#0000# shows the SW version.
Latest software version: V 5.06 (09.12.99) RAE-2
V 5.02 (26-08-99)RAE-2 V 4.05 RAE-2
Free SMS Tip 1st Way: 1. turn our phone off. 2. turn it on and enter your pin. 3. enter *#746025625# 4. now "SIM CLOCK STOP ALLOWED" will be displayed. now you can send sms for free. if you turn your phone off and later on you have to reenterthis code!!! In some Networks it doesn't work!!!
alcatel – poza de budy, in -=coduri telefoane=- · 11.5KB
. 